A list of the contents of this article:

How to boil the new iron pot bought?

Put the new iron pot into the pool for cleaning, do not use any detergent. After cleaning, put on the gas stove and turn on the low heat to dry. In an iron pot heated by friction with lard blocks, the noodles inside the iron pot should be rubbed evenly and repeatedly. Turn off the heat and wait for the iron pot to cool naturally. Clean the iron pot with clean water and wipe it with a soft brush. Wipe the washed iron pot with a clean rag.

Method 1: bring boiling water to a boil. The new iron pot you just bought can burn red on the gas stove; next, pour the boiling water into the hot iron pot and bring it to a boil; it takes about 10 minutes to boil, and then pour out the water. Method 2: sandpaper friction. The new pot you just bought can grind off the rust with sandpaper, then wash it twice with clean water, and finally put it on the gas stove to dry.

Cleaning: for the purchased iron pot to be cleaned after unpacking, you can use detergent for a cleaning, and then wipe clean, waiting for the following step. Burning: as far as the iron pot is concerned, the pot must be fired, so that the impurities in the pot can be removed. The quality of the iron pot after firing is very good.

How to open the new iron pot non-rusting non-stick pot the new iron pot is not rusty, non-stick pot in the process of use, the following are the steps to open the pot: prepare tools: new iron pot, dishcloth, detergent, cooking oil. Clean the iron pot: first clean the dust and impurities on the surface of the new iron pot with a dishcloth. Smear detergent: apply the detergent evenly on the inner wall of the iron pot, pay attention to smear evenly to avoid residue.

The method of buying a new iron pot and boiling it

1. Method 1: boil the newly bought iron pot with boiling water and burn it red on the gas stove. Next, pour the boiling water into the hot iron pot and bring it to a boil. It takes about 10 minutes to boil, and then pour out the water. Method 2: grind the new pot you just bought with sandpaper, you can wear off the rust with sandpaper, then wash it twice with clean water, and finally put it on the gas stove to dry.

2. Put the new iron pot into the pool for cleaning, do not use any detergent. After cleaning, put on the gas stove and turn on the low heat to dry. In an iron pot heated by friction with lard blocks, the noodles inside the iron pot should be rubbed evenly and repeatedly. Turn off the heat and wait for the iron pot to cool naturally. Clean the iron pot with clean water and wipe it with a soft brush. Wipe the washed iron pot with a clean rag.

3. The first step of cooking the domestic iron pot: clean the whole pot. After the pot is bought, put the iron pot under the faucet, wipe every corner with a soft cloth, wash off the sundries and dust in the casting process, and do not use any washing products. Step 2: believe that the iron pot is an open fire, the fire is turned to a minimum, and slowly dry all the water droplets in the pot.

The correct way to boil the iron pot

1. Put the new iron pot into the pool for cleaning, do not use any detergent. After cleaning, put on the gas stove and turn on the low heat to dry. In an iron pot heated by friction with lard blocks, the noodles inside the iron pot should be rubbed evenly and repeatedly. Turn off the heat and wait for the iron pot to cool naturally. Clean the iron pot with clean water and wipe it with a soft brush. Wipe the washed iron pot with a clean rag.

2. The method of opening the new pot is as follows: cleaning: the newly bought iron pot will have a layer of residual oil left by mechanical processing. if it has not gone through the iron pot, the mechanical residual oil will flow into the dish, which is very bad for the health. So wash it carefully. Dry burning: dry the water after cleaning, put it on the fire and burn off the coating on the surface.

3. If the purpose of applying lard in front is to put a "protective cover" on the iron pot, then the last step is to add a "golden bell cover" to the iron pot. Only by adding this layer of golden bell cover can the new iron pot be really completed.

4. Clean the new iron pot first, because there will be some oil stains on the surface of the iron pot during the production process. We will clean it with detergent, but we should be careful not to scrub it with wire balls for the first time. The washed iron pot begins to boil, first heat the iron pot, not too much fire, and dry over a small heat.

5. Thoroughly clean the iron pot, put the iron pot under the faucet, put some cleaning essence, and scrub it several times with a hard brush or towel gourd pulp, mainly to remove impurities and some mechanical oil.

6. There are many different ways to open the pot. Today, I would like to share with you a correct way to open the pot. Let's have a look.

How to boil an iron pot? how to boil a stainless steel pot?

How do I boil a stainless steel pot? Today, the editor will explain how to open the iron pot for you one by one, clean the iron pot again, wash it normally with detergent, dry the water with paper after washing, put the pig fat into the pot, and stick the meat noodles in the pot. Turn on the low heat, hold the meat in the dish clip to wipe the pan noodles, wipe until the lard bubbles for the first time, take out the meat, wait for the iron pot to cool, and soak in the lard.

The boiling method of all kinds of new pot: pig iron pot: (1) before the first use, the pot does not need to be washed and burned directly over the fire. (2) you can use a high fire to burn the pot, and you will find that the color of the pot changes (first blackened and then restored to the original color). Be careful not to turn red or smoke, otherwise it is a sign that the pot is about to burn out. When the pot is burned from the primary color to black and then to the primary color, you can leave the fire.

After buying a stainless steel pot, remember to clean it first, heat the bottom of the pot, pour in a little white vinegar, and turn off the heat when it is boiling hot. Brush the whole inside of the pot with hot vinegar with a steel brush and wash it everywhere, so as to remove dirt and impurities from the stainless steel pores. After brushing it clean, pour out the white vinegar and rinse with clean water.